7020+500+500 ???

[acer]

ako mam skontrolovat mgcam cez telnet ??
mg_cfg som snim nic nerobil

# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }

# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }

# AU
# 00 is ignored (default)
# 01 enable AU
# 02 AU Auto
A: { 02 }

# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }

# key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }

# network retry, use summ for several options
# 00 disable (default)
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 04 }

# network ecm timeout in seconds
K: { 10 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
O: { 00 }

# on screen display Options
# 03 default
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }

# Log options
# 00 Off (default)
# 01 Network
# 02 console
# 03 both
L: { 00 } 172.16.1.1 28007

# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup,
# same syntax as restore.list
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 03 both caches
H: { 00 }

# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }

# debug
# 00 off (default)
# 01 on
D: { 00 }

[Zoli]

ako mam skontrolovat mgcam cez telnet ??
mg_cfg som snim nic nerobil

# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }

# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }

# AU
# 00 is ignored (default)
# 01 enable AU
# 02 AU Auto
A: { 02 }

# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }

# key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }

# network retry, use summ for several options
# 00 disable (default)
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 04 }

# network ecm timeout in seconds
K: { 10 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
O: { 00 }

# on screen display Options
# 03 default
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }

# Log options
# 00 Off (default)
# 01 Network
# 02 console
# 03 both
L: { 00 } 172.16.1.1 28007

# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup,
# same syntax as restore.list
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 03 both caches
H: { 00 }

# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }

# debug
# 00 off (default)
# 01 on
D: { 00 }

Nejde Ti nič na DM500 odkódovať? Ani cez EMU?
Ak Ti nejde nič, je možné, že nemáš ani binárny súbor mgcamd, alebo má nesprávne atribúty, alebo nemáš dobrý spúšťací script.
Ak Ti EMU ide a nejde len share, tak nemáš správny newcamd.conf alebo nie je v správnom adresári. Samozrejme za predpokladu, že server beží a je v ňom aj príslušný user.