Stránka 1 z 2 12 PosledníPoslední
Zobrazují se odpovědi 1 až 15 z 23

Téma: Kernel Panic.....

  1. #1
    Registrovaný uživatel
    Založen
    25.05.2007
    Příspěvky
    73
    Post Thanks / Like
    Downloads
    0
    Uploads
    0

    Kernel Panic.....

    Hi to ALL,

    I used Hyperterminal and connect to UFS with serial Cable.

    I erased this block:

    erase A0200000 A029ffff
    erase A02A0000 A04Dffff
    erase A04E0000 A0Adffff
    erase A0C00000 A0ffffff

    After i turn on ufs910 ,I show on ufs910 display "Kathrein UFS-910 ", and thats all .....
    remote control doesn't working, and i can not make a update via USB.


    P L E A S E H E L P......(mayday mayday mayday).

    Regards.
    Nachmany
    Přiložené obrázky Přiložené obrázky

  2. #2
    Registrovaný uživatel
    Založen
    04.07.2007
    Příspěvky
    11
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    boring, this problem is 1000 times solved before

  3. #3
    Registrovaný uživatel
    Založen
    25.05.2007
    Příspěvky
    73
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Citace Původně odeslal concelate Zobrazit příspěvek
    boring, this problem is 1000 times solved before

    Hi,

    sorry, but what can I do ?

    Nachmany

  4. #4
    Registrovaný uživatel
    Založen
    04.07.2007
    Příspěvky
    11
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    in case if something went wrong during updating/flashing your receiver and it fails to start because of missing kernel, emergency partion.. i have created an "emergency-kernel" with an embedded emergency ramdisk - so you can revive your receiver as long as you haven't killed uboot.

    follow this steps:

    1.) install a tftp-server (windows e.g. http://perso.orange.fr/philippe.jounin/tftpd32.html)
    2.) download the "emergency-kernel" and copy "emergency.ub" to your tftp-share --> http://www.megaupload.com/de/?d=66RV985P
    3.) connect the receiver through serial and network port and start the terminalapplication on the serial port
    4.) power on the receiver and press immediately <enter> on the terminal, you should see the uboot prompt (STB7100-Ref>)
    5.) on uboot prompt set the box ip with "set ipaddr 192.168.x.x" (you have to adapt x.x to your settings, both have to be in the same subnet)
    6.) on uboot prompt set the tftp-server ip with "set serverip 192.168.x.x" (you have to adapt x.x to your settings, both have to be in the same subnet)
    7.) on uboot prompt copy the kernel with "tftp a4000000 emergency.ub" into memory
    8.) plugin the prepared usb-stick (you can get a full update of all partitions here --> http://www.megaupload.com/de/?d=63MJTFN9)
    9.) on uboot prompt start the kernel from memory with "bootm a4000000"

    now the emergency-system should boot and starting to update...
    Naposledy upravil concelate : 29.07.2007 v 11:57

  5. #5
    Registrovaný uživatel
    Založen
    25.05.2007
    Příspěvky
    73
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Citace Původně odeslal concelate Zobrazit příspěvek
    5.) on uboot prompt set the box ip with "set ipaddr 192.168.x.x" (you have to adapt x.x to your settings, both have to be in the same subnet)
    6.) on uboot prompt set the tftp-server ip with "set ipaddr 192.168.x.x" (you have to adapt x.x to your settings, both have to be in the same subnet)
    Hi,

    Thanks for the detailed reply.
    In step 5 and 6 you use the same command "set ipaddr 192.168.x.x" - could it be a typo, or is it the same command, both to set the box ip and the tftp-sevre ip?

    Thank you,

    Nachmany

  6. #6
    Registrovaný uživatel
    Založen
    04.07.2007
    Příspěvky
    11
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Sorry for that, at step 6 set the tftp server ip with: "set serverip 192.168.x.x"

  7. #7
    Registrovaný uživatel
    Založen
    25.05.2007
    Příspěvky
    73
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    T H A N K S TO concelate ...........!!!!!
    Now I have 1.03 firmware.......

    Satforum is number 1 !!!!!!!


  8. #8
    Registrovaný uživatel
    Založen
    05.07.2007
    Příspěvky
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    hi, all

    STB7100-REF> tftp a4000000 emergency.ub
    Using MAC Address 00:50:FD:FF:67:14
    TFTP from server 192.168.0.1; our IP address is 192.168.0.6
    Filename 'emergency.ub'.
    Load address: 0xa4000000
    Loading: T T T T T T T T T T
    Retry count exceeded; starting again
    TFTP from server 192.168.0.1; our IP address is 192.168.0.6
    Filename 'emergency.ub'.
    Load address: 0xa4000000
    Loading: checksum bad
    T checksum bad
    T checksum bad




    Filename 'emergency.ub'.
    Load address: 0xa4000000
    Loading: T T T T T T T T T T
    Retry count exceeded; starting again


    edit:
    reinstal win, OK , THANK YOU! @concelate
    Naposledy upravil tadel : 24.07.2007 v 09:15

  9. #9
    Registrovaný uživatel
    Založen
    04.07.2007
    Příspěvky
    11
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    download emergency.ub again und replace it, maybe the current file is bad...
    and stop firewall and antivirus on the pc

  10. #10
    blacklamb
    Host
    Hi All
    Same problem
    This link is not working. Please help.

  11. #11
    blacklamb
    Host
    This is my problem.
    NET: Registered protocol family 2
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    NET: Registered protocol family 1
    usb 1-1: new high speed USB device using ST40-ehci and address 2
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    usb 1-1.4: new high speed USB device using ST40-ehci and address 3
    IP-Config: No network devices available.
    scsi0 : SCSI emulation for USB Mass Storage devices
    UDF-fs: No VRS found
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)

  12. #12
    Registrovaný uživatel
    Založen
    25.05.2007
    Příspěvky
    73
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Hi,

    You can see thet your reciver detail, it is like the detail in attaced file on the top (see post number 1).
    I fixed it , so You can fix it.

    Nachmany

  13. #13
    blacklamb
    Host
    Thx for the help.
    Working.
    But only works whit Hyper terminal pivate edition. Simple win version no.

  14. #14
    dboxforever
    Host
    when using Hyperterminal from Windows you have to deactivate flow-control.

  15. #15
    Registrovaný uživatel
    Založen
    06.04.2004
    Příspěvky
    299
    Post Thanks / Like
    Downloads
    1
    Uploads
    0
    Hi I have big problem. I conect to UFS-910 via Hyperterminal. But dont me work any more. Dont write eny.



    B
    aodr :TS7b01-0bmaodr

    U
    B-oo t.1.1 2S(LTNIXU2_0_1p )F(be2 70270- 1 :37328

    RDMA :3 2BM
    rwti eitemo tu= 1 ,lcco k =04
    rwti eitemo tu= 1 ,lcco k =04F



    Board: STb7100-mboard


    U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 27 2007 - 13:37:28)

    DRAM: 32 MB
    write time out = 1, clock = 40
    write time out = 1, clock = 40
    Flash: 16 MB
    In: serial
    Out: serial
    Err: serial
    pll0 freq 531
    pll1 freq 400
    Net: VFD_Driver Init
    VFD_Controller Type : NEW Kathrein VFD
    Button_value = 7
    Hit any key to stop autoboot: 0
    ## Booting image at a0040000 ...
    Bad Magic Number
    STB7100-REF>

Informace o tématu

Users Browsing this Thread

Toto téma si právě prohlíží 1 uživatelů. (0 registrovaných a 1 anonymních)

Podobná témata

  1. boot kernel DM5620
    Založil alfons v sekci fóra DreamBox - Firmware/Software/Hardware
    Odpověďmi: 0
    Poslední příspěvek: 27.10.2005, 16:19
  2. Multi-lun support
    Založil ballpoint v sekci fóra DreamBox - Firmware/Software/Hardware
    Odpověďmi: 0
    Poslední příspěvek: 10.07.2004, 14:02

Štítky pro toto téma

Záložky

Záložky

Pravidla přispívání

  • Nemůžete zakládat nová témata
  • Nemůžete zasílat odpovědi
  • Nemůžete přikládat přílohy
  • You may not edit your posts
  •