Zobrazují se odpovědi 1 až 12 z 12

Téma: Remote control stops to work...

  1. #1
    Registrovaný uživatel Avatar uživatele bpl
    Založen
    31.07.2007
    Bydliště
    Sweden
    Příspěvky
    8
    Post Thanks / Like
    Downloads
    0
    Uploads
    0

    Remote control stops to work...

    Hello,

    I have a BIG problem. My remote control for Kathrein stops to work after 5 minutes. If I restart the box with the switch on the back of the box the remote still don't work. The only thing that makes the remote to operate again is to do a flash earase and flash the box again with SF 1.03. New batterys does'nt help

    Please help... any suggestions?

  2. #2
    Registrovaný uživatel Avatar uživatele bpl
    Založen
    31.07.2007
    Bydliště
    Sweden
    Příspěvky
    8
    Post Thanks / Like
    Downloads
    0
    Uploads
    0

    Exclamation Maybe a solution...

    Remote control no longer responding. Receiver or remote control command set may have been unintentionally changed Set infrared code 1, as described in operating manual under
    “Remote Control RC 660”; check batteries.

    Remote control RC 660
    The RC 660 remote control supports up to four devices (supplied as
    standard with the RC 660) as well as the receivers of the UFD 5xx
    (not UFD 552, 554, 558) and UFD 4xx families.
    First switch all receivers off at the power switch.
    To configure a receiver to an infrared code:
    Switch on the relevant receiver.
    On the remote control simultaneously press
    Address 1 = exit + 9 + 1
    Then switch the receiver off again at the power switch and do the same
    for the other units (exit + 9 + 2 for second receiver; exit + 9 + 3
    for third receiver and exit + 9 + 4 for fourth receiver).
    Make sure only one receiver is on at a time!
    To switch the remote control to an infrared code:
    When you have configured all receivers to their infrared code, to switch
    between units on the remote control do the following:
    For the first receiver’s remote (address 1) press exit + 1; for the
    second receiver exit + 2; for the third receiver exit + 3; and for the
    fourth receiver exit + 4.

  3. #3
    jed
    Host
    Hi, I had the same problem,you must reflash your box,,and then you will have the firmware of 1,03.
    Then start software upgrade by satellite but not for the channels. and i hope it shoul work for you also.
    Best of luck

  4. #4
    afzalsher
    Host
    Citace Původně odeslal jed Zobrazit příspěvek
    Hi, I had the same problem,you must reflash your box,,and then you will have the firmware of 1,03.
    Then start software upgrade by satellite but not for the channels. and i hope it shoul work for you also.
    Best of luck
    I also get the same problem. I reflash but this is no solution to reflash every 5 minutes. There must be something wrong. Can any soul tell us what to do. The message pbl is not very clear to me.

    Regards,
    Afzal

  5. #5
    jed
    Host
    Afzal, bpl wrote the codes to connect the multiple recievers with one remote,but this is not the case.
    After reflashing just do the satellite upgrde and that is it,,,,up up

  6. #6
    afzalsher
    Host
    Dear jed,

    I have reflashed many times to get rid of the problem, but the it returns when you zap around a little , and specially fast.

    Did your box started behaving properly for all time after reflashing?

    Reagrds
    Afzal

  7. #7
    jed
    Host
    Hi afzal,
    Yes no problem after reflashing.Here are some steps to follow;
    1.after reflashig try to move cursor of remote slowly to complet the First Installation steps
    2.Then see if the channels are coming otherwise go to channel search for only Astra 1
    3.go to satellite Software Upgrade , it will take nearly 20 minutes , after rebooting there will be no problem and believe me that works for me.
    Good Luck ('''You must move the remote cursor slowly'''')

  8. #8
    afzalsher
    Host
    I could not make it work so I cahnged my box, and now everything is perfect. So that would mean that some boxes have problems in the hardware.

  9. #9
    pete102
    Host
    I have had this problem too, it seems that it could be releated to several things, mgcamd seems to make it worse, as do some channel lists.

    It works fine if I dont use mgcamd and stay on FTA channels that I have scanned in, not uploaded.

  10. #10
    Registrovaný uživatel
    Založen
    13.06.2008
    Příspěvky
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    HI
    i have a starsat receiver.its remote control stops workin when goes on some channel.and i have to turn off the receiver .

  11. #11
    Registrovaný uživatel
    Založen
    05.07.2008
    Příspěvky
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Aky Image mam pouzit pre Kathrein UFS910, ako to nainstalovat? Ako nainstalovat zvysok? Aby som mohol zdielat karty a pozriet si DigiTV? hrac@hrac.sk

  12. #12
    Registrovaný uživatel
    Založen
    22.09.2002
    Bydliště
    CZ
    Příspěvky
    849
    Post Thanks / Like
    Downloads
    10
    Uploads
    0
    Citace Původně odeslal hrachrac Zobrazit příspěvek
    Aky Image mam pouzit pre Kathrein UFS910, ako to nainstalovat? Ako nainstalovat zvysok? Aby som mohol zdielat karty a pozriet si DigiTV? hrac@hrac.sk
    Zkus AAF 2,0b třeba z této stránky. Jsou tam i další potřebné věci, jako setting editor a pod.

    www.ump2002.net

    Jestli začínáš a nemáš potřebné znalosti, budeš to mít těžké.
    Přečti si toto fórum, sekci Kathrein od začátku, tam máš postupy jak flashovat,
    jak na setting, projdi i další fóra.

    Jinak bych Ti doporučil nechat si udělat první instalaci odborníkem...
    bob

Informace o tématu

Users Browsing this Thread

Toto téma si právě prohlíží 1 uživatelů. (0 registrovaných a 1 anonymních)

Podobná témata

  1. Gbox remote control center
    Založil trevor v sekci fóra DreamBox - Firmware/Software/Hardware
    Odpověďmi: 0
    Poslední příspěvek: 25.11.2006, 17:04
  2. EPG 1.01 by Spallared doesn't work on SF 3.2
    Založil redneck eyeball v sekci fóra DreamBox - Firmware/Software/Hardware
    Odpověďmi: 0
    Poslední příspěvek: 11.05.2004, 13:39

Štítky pro toto téma

Záložky

Záložky

Pravidla přispívání

  • Nemůžete zakládat nová témata
  • Nemůžete zasílat odpovědi
  • Nemůžete přikládat přílohy
  • You may not edit your posts
  •